|
First, not flat. No provision for add-on clamp.Customer service is certainly friendly, but actual service is quite slow. Recommended: get your own piece of oak or other hardwood (1/4" thick) and make your own zero clearance insert for almost $0. You must gently tap the fence after tightening 3/4's of the way to get to your desired position.
Minimal adjustments by four shallow set-screws. It is moderately quiet, but with an odd sound, no the jet engine wind-up/wind-down I'm used to. Still, according to other reviewer's, this is the best they have ever seen. Shop Fox fence un-usable due to damage and missing parts. This is a problem with using the very heavy cast iron wings because it makes the saw less stable. I can see that replacement parts and accessories would be a real headache.
I already replaced with a grade 8 hex bolt (with mill marks sanded flush) and a Teflon glide from a chair leg) attached to that with JB epoxy).The table stand is no wider or more stable than other "portable" saws. Let's face it, almost no DIY'er or contractor is going to buy a panel saw for sheet goods, andd at least half my cutting chores are with plywood.The miter that comes with the unit is a joke. Accurate gauge. Another problem is the back "glide" is actually an upside-down carriage bolt with a piece of teflon stuck on the head. Yes. Cast iron wings obviously from different lot as noticeable misalignment to main table.
Remember, this is an import saw, made in R.O.C. Shipping pallet contaminated with fungus/mushrooms. I think not. You have to provide your own shims. Single plastic glide insert.
The actuakl contact curface is just 1/8th".Again, a plain steel piece - easilt bent/damaged. That brings up another problem in the set-up of the fence. Motor transome not spring or hydraulic dampened, and juts out well past end of table compared to other saw brands. Drive belt is "no-name" quality, metric size, and does not sit flush in motor pulley or spindle pulley.
Cheesy stick on ruler and easily damaged/misaligned magnifying sight). The dust collection pan is worthless - since the four sides of the frame remain open and any cross breeze counteracts the vacuum, blowing debris 2 to 4 meters away.The blade height wheel layout is terrible. You will need several if you change brands or type of blade due to differences in tooth offset/rake.To its' credit, the saw does operate very smoothly. Nope - stick on decal, not even cast, let alone engine engraved. Having to reach over to pull through long work pieces is a safety issue.The blade table insert.
The fit and finish are only fair to poor (enamled, not powder-coated finish. Cheap attachment hardware: ungraded plain steel and not accurately made. The freespin handle is so close to the lower part of the fence support rail that 1) cannot be seen unless bending over (a dangerous practice with saw running) and 2) I am constantly hitting my medium sized hand on the sharp edge underneath (too bad I cannot show you a digital photo of resulting cuts to right hand).Why other reviews think the Shop Fox fence is the last word in fences, I have no idea. Very rough stroke - which causes control concerns.
However, given the damage, length of time to receive, the low quality casting/machining, the crude Shop Fox fence, and shipping costs/hassle; better to go to your local hardware store or tool retailer and get a Delta/Ridgid/JetOK - so this is a contractor quality saw and not a cabinet-maker's dream. Both boxes significantly damaged. The additional wings are almost a necessity when cutting full sheets of plywood. Limited adjustments for paralell and perpendicular. That is, tightening the cam lever lock results in the fence shifting as much as 1/16th off from original position. and that Grizzly is a marketing company, not a true manufacturer.Overall, the saw is OK.
Grizzly had best overall rating - though limited number of reviews.Assembly and set-up time for a pro: 2 hoursInitial impressions: not overly impressedItem arrived in two boxes. If any significant pressure is applied to the fence (as in using the miter guage OR tweaking a piece of plywood too much), the fence becomes mis-aligned. Shipping weight significantly overstated by more than 10% net.On initial inspection, very poor casting and machining EXCEPT motor and spindle, which when set-up ran at less than 1/1000th runout.
Very annoying. The main annoyance is that the Shop Fox, unlike every other saw in this price range, is MISSING a BACK CLAMP. Heavy.
Third, cannot achieve max depth of cut BECAUSE blade washers push insert completely out of table. My background: professional engineer and contractor.Reason for purchase: Replacement for Sears 10" contractor saw.Why Grizzly.: Read reviews on all the majors (Delta, Jet, etc). Second, as another reviewer pointed out, deep cast logo catches small and odd shaped pieces.
It also means you cannot possible add additional wings without having adjustable outrigger legs.
I must say, for the money there is no better saw on the market. You can see the quality in each piece as you assemble the saw.
Highly recommended. There is a huge difference between an 'engineered' product and a 'mass-produced' product.
You can tell that Grizzly spent a great deal of time 'engineering' this product. Its that nice.
I purchased this saw after reading the reviews here. This thing is first class.
Grizzly could easily get away with selling this saw for $1000+.
I am impressed by the surfaces of the table and wings. Everything went together well. Add to this a relatively thin stamping that the motor sits on and you have a resonance issue. For the money this saw cannot be beaten. It is heavy but not as big as I expected it to be.
The Shop Fox fence feels and works just like the bessemer on the Jet. The box arrived quickly. the motor hangs on the belt by the pulley, yet the center of gravity of the motor is way out on the other end. We tracked this down to the motor mount. One wing needed a tape shim and the other was perfect. The trunion needed a couple of hits to be in adjustment. The saw went together in about three+ hours. No change of sound from the motor, nothing, just a super clean cut.
I think I got lucky. If you buy one you might as well order a zero clearance insert as the one included isn't worth using if you are cutting on small stock. When I am cutting I cant really tell the difference with the Jet other than a small vibration. I didn't want to invest 1200+ in a cabinet saw so I started to look into contractor style saws, I read the reviews and bought a Griz. After cutting is when I notice the difference with the Jet. Look around the back of the saw and check out the sawdust thrown all over the place.
Since I don't tilt the blade often I will just make a cardboard block for the back.I am really very pleased with this machine. The on/off is better on the Griz. Up until now I have been using a friends Jet cabinet saw and loving it. The fence arrived at the same time in another box. I managed to do this with the saw on its feet. I ran some.75 mdf through and the blade (forest WW2) didn't even notice.
It is way better quality and value than the cost shows. I know this page is covered with glowing reviews for the grizzly go444z, but I am compelled to ad one more. The instruction book is easy, clear and well illustrated. I was worried about this when I first ran the saw but now that I have run through a couple of projects I don't notice anything and it certainly doesn't effect the quality of cut.
I have had great service from their web-site, and I intend to purchase additional equipment from them (as soon as I can convince my wife to let me) I liked it so much that I talked a buddy into retrofitting his older saw with it, and he loves it too.The only problems that I have noted with this saw are as follows:- The Grizzly logo blade insert looks great, but can catch on some smaller pieces - The Zero Clearance inserts that Grizzly sells are very good.- The drive belt cover clearance can become a problem if the blade is lifted to full extension. Assembly was a snap, and the saw was in almost perfect alignment right out of the box. I would HIGHLY recommend this saw to anyone who is looking to upgrade their shop with a truly accurate table saw. After much research, I settled on the Grizzly G0444Z Contractor style saw.
The fit and finish of this saw is excellent, and the cast-iron wing extensions are GREAT. After about an hour of assembly (with my sons help) I ran test cuts with a Forrest 60 tooth blade, and found them to be virtually perfect.The Shop-Fox Aluma Classic fence is probably the easiest fence that I have ever used, and I would HIGHLY recommend it. This is a right tilt saw (Grizzly has added a Left-tilt of the same model - G0576) with cast iron wings and comes wired for 220V. I have been an amatuer woodworker for a number of years, however I always found that my work was limited in quality due to various problems with my old table saw (Old Sears contractor type). I preferred the cast iron wings for the weight and solid structure that they provide, and the 220V motor has more power for heavier cutting.I picked up my saw at the receiving shipper in my area, since they only drop ship to the end of your driveway (Take Note - This saw weighs 300LBs and is VERY hard to lift, even in pieces) - the shipper loaded it into my truck for me, which saved me a ton of work.
Check the alignment of the cover when you install it, very carefully.- The dust collection cover is really an add-on, and I needed to add some additional fasteners to ensure that it didn't move around.- The Miter gauge that comes with the saw is OK, however to get truly accurate miter cuts, I would highly recommend you replace it with the Incra V27 - a VERY good, VERY accurate, and VERY reasonably priced Miter Gauge.Overall, this saw is absolutely THE best-buy on the market (in my opinion) for a Contractor Style saw.
Compared to the over-priced saws at Lowe's and Home Depot, this is the way to go. I had to use a pry bar to move the trunions into alignment, but could only do this after flipping the assembled table upside down. He recommended that I start with the G0444Z since I'm new to woodworking. My saw was quite mis-aligned when it arrived at my house.no doubt due to the rough handling by the shippers. I re-wired my garage to 220V and the saw works great. The dust collector is a bit cheesy, but usable. Overall, I like the saw. My only complaint is the trunion adjustment process to make the blade parallel to the miter slot.it is a pain in the butt.
This is not an easy task since the saw weighs something around 300 pounds. I covered the back of the saw with plastic to help contain the dust. My father-in-law has a Grizzly cabinet saw and loves it. It is very sturdy and has tons of power. After several exhausting hours of adjustment, I got the thing aligned.
|
